logo
搜索
Search
img
新闻中心

What is the standard of switch socket panel screws? ? ?

  • Categories:Company News
  • Author:
  • Origin:
  • Time of issue:2020-12-29 13:54
  • Views:

(Summary description)With the innovation of new technologies and new processes in industrial modernization, modern industrial equipment, automobiles, engineering machinery and customers have higher and higher requirements for the quality of fastener products, and the technical parameters are constantly improving.

What is the standard of switch socket panel screws? ? ?

(Summary description)With the innovation of new technologies and new processes in industrial modernization, modern industrial equipment, automobiles, engineering machinery and customers have higher and higher requirements for the quality of fastener products, and the technical parameters are constantly improving.

  • Categories:Company News
  • Author:
  • Origin:
  • Time of issue:2020-12-29 13:54
  • Views:
Information
With the innovation of new technologies and new processes in industrial modernization, modern industrial equipment, automobiles, engineering machinery and customers have higher and higher requirements for the quality of fastener products, and the technical parameters are constantly improving.
 
Therefore, the screw people have higher and higher requirements for the fastener standards. If the standards are not checked, any work will be delayed. If the work efficiency is improved, the fastener standards can be inquired more quickly and accurately? After reading this article, you will understand.

1. The evolution history of fastener standards

In the era of Archimedes, spiral water lifting equipment was available. After the European Industrial Revolution, various machinery and equipment needed a lot of use and maintenance. Later, it was discovered that the threads of each component were different.
In 1841, Joseph Whitworth unified the thread; proposed that the angle of the thread surface should be 55° as the standard, and the number of threads per inch should be defined according to different diameters. This kind of thread is called Wyeth thread, also known as inch mechanical thread (inch thread).

img
 

In 1867, the Americans proposed 60° as the standard, that is, the number of threads per inch should be defined according to different diameters, and later developed into American mechanical threads (American threads).
In 1948, the United Kingdom, the United States and Canada reached an agreement on a unified standard thread, and adopted this as the standard for all countries that use imperial units. The unified thread was born. The unified thread adopts the same measurement method as the American thread, and it is also a 60° standard cusp angle.
However, the root radius of the unified standard thread is longer, which proves to be more advantageous than the DIN metric thread profile. This led to the production of ISO metric threads, which are now common Chinese metric mechanical threads (metric threads, metric threads) starting with M.
Since 2010, there have been three major series of international standards, namely the metric standard system (including ISO, EN, DIN, JIS, IS, GB), the imperial standard system (including BS, AS, JIS, ASME), and the American standard system ( Including ANSI, ASME, SAE, ASTM).

 

 img

2. What problems did the screwers encounter when checking the standards

At present, there are not only many standards for fasteners, but also many versions; when I look at the drawings, I often see that the standards adopted on the drawings are all obsolete standards. Then, it is particularly important to find the platform for the fastener standard inquiry.

Related News:

The importance of hardware in doors and windows

The importance of hardware in doors and windows

Window stays, hinges, handles, buttons and other hardware in doors and windows are probably ignored by many people, but the quality of the hardware will completely affect the normal use of doors and windows. How do they affect it?
Hardware common sense: screw strength torsion test

Hardware common sense: screw strength torsion test

Screw strength test: 1. Turning force test: The twisting force of a product shows its ability to resist being twisted in half. Various standards have minimum requirements for the torsion force of self-tapping screws. In this test, the screw is clamped in a chuck with a tapped middle part on the torsion test tool, and then a torque wrench is used to apply force until the screw is twisted. If the torque does not exceed the minimum requirement, the product is unqualified. Unqualified indicates that the screw is too soft or the thread diameter is too small. 2. Locking test: This test is to lock the screw to a test board, this board has the specified hardness, thickness and aperture. If the screw is locked through the test board, but the thread is deformed, the product is not qualified. Unqualified indicates that the surface hardening treatment of the screw is too shallow or too soft. 3. Locking torque test: This test is only required for the screw rolled by the screw. When the lock test is performed, the minimum lock torque of the test board is observed. If the torque exceeds the specified standard value (the standard value is based on the size of the screw and the surface treatment), the product is not qualified. Unqualified shows that the surface of the screw does not have enough lubricity, or the thread is formed improperly and requires more torque.
Basic knowledge of Phillips screwdriver specification selection

Basic knowledge of Phillips screwdriver specification selection

Phillips screwdrivers generally have 7 specifications from small to largest ph000 ph00 ph0 ph1 ph2 ph3 ph4 The approximate relationship between the diameter of the screwdriver shaft and the specifications: 4mm~4.5mm rods generally do cross Ph1, which can cover ph000 ph00 ph0 ph1 This series is basically a precision series, disassembly and assembly of small electronic devices, glasses, watches, radios, tape recorders, etc.. Must! This is mainly a set, of which ph000 is very small, not a lot of use The 6mm rod is generally used for the Phillips Ph2 specification. This is the most commonly used specification in the medium-sized screwdriver, so you can buy one separately and use it for the fastening screws of the display, radio, TV and other housings, transformer fixing, etc. It is also a Ph2 head that makes furniture door screws. The 8mm rod is used for Ph3, and the 10mm rod is used for Ph4. Basically, it may be used in mechanical equipment. It is rarely used in electronic assembly, unless it is used as an electric box controller... So the combination scheme of Phillips screwdriver configuration is roughly: Precision screwdriver set below 4mm rod + a separate Ph2 screwdriver If you consider that the handle of the suit is too thin to focus on, you can also configure a Ph1 screwdriver separately. It is not a problem if it is not configured. Nothing is too particular about a word There are many types of star batches, and the general suits start from T6, but some modern mobile phones have the smallest use of T5, so generally suit + T5 can hit the world. About the material experience: From lowest to highest Medium carbon steel-high carbon steel-crv- S2- S2 plus titanium oxide coating-S2 plus diamond coating. For example, wera's most high-end Beatles can increase friction after using diamond coating without increasing the force or slipping screws.
logo

Copyright © Jiangmen Jinhe Hardware Products Co., Ltd. 粤ICP备18077102号

Address: E1, Self-edited Second District, Building 1, No. 8, Fengtai 2nd Road, Tangxia Town, Pengjiang District, Jiangmen City

Technical support: www.300.cn Jiangmen